Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin
Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin
Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin
Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin
Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin
Diamond Hard Coat 607 2:1 | 12L Kit UV-Resistant Epoxy Resin

Diamond Hard Coat 607 2:1 | 12L Kit Epoxy Resin

$315.00 $236.25

or 4 payments of $59.06 with Afterpay Info

Add to Wishlist

american expressapple paymasterpaypalvisaafterpay

The Diamond Hard Coat 607 12L Kit is a clear 2:1 epoxy coating resin for larger timber, tabletop, concrete and fibreglass projects. It is formulated for enhanced resistance to UV discolouration and cures to a hard, high-gloss clear coat. Very low viscosity gives fast bubble release, and batches of up to 16 litres can be mixed in an open pail.

Product details

Kit size
12L
Mix ratio
2:1 by volume
Working time
Approx. 30 minutes at 25 °C
Pour depth
1–2 mm per coat
Coverage
1 litre ≈ 1 m² at 1 mm
Set time
Approx. 1 day at 20 °C (1–2 mm)
Full cure
Approx. 3 days
Heat resistance
Up to 80 °C once cured

Key features

Enhanced UV resistance
Very low viscosity
Rapid bubble release
Low odour
Hard, high-gloss clear finish
2:1 mix ratio

What's in the 12L Kit

Part A
2 x 4L resin
Part B
4L hardener
Coverage
≈ 12 m² at 1 mm

Best for

Canvas coating
Timber and tabletops
Concrete
Fibreglass laminating
Decoupage
Adhesive
Filling shallow cavities

How to use Diamond Hard Coat 607

1
Set up
Work between 20 °C and 30 °C. Raise your piece a few centimetres above the work surface so excess resin can run off.
2
Measure 2:1
Measure 2 parts resin (Part A) to 1 part hardener (Part B) by volume into a straight-sided mixing container.
3
Mix thoroughly
Mix for several minutes until the mix is evenly clear. For batches up to 16 litres, use a paint mixer on a drill at slow speed.
4
Pour
Pour onto your surface and let it flow over the edges. To tint, mix a larger batch and split it into smaller containers.
5
Release bubbles
Lightly pass a propane torch flame over the surface to help release bubbles.
6
Clean the edges
After about an hour, wipe or scrape any drips off the edges.
Pour 1–2 mm per coat. Build thicker finishes in layers.

FAQs

What is the mix ratio for Diamond Hard Coat 607?+
2 parts resin (Part A) to 1 part hardener (Part B) by volume. Measure into a straight-sided container and mix for several minutes until the mix is evenly clear.
How long is the working time?+
A 250mL mix stays fluid for around 30 minutes at 25 °C. Larger batches and warmer rooms shorten the working time.
How thick can I pour each coat?+
Pour 1–2 mm per coat. Diamond Hard Coat 607 is a coating resin, not a deep-pour casting resin.
Can I cast or pour into moulds with Diamond Hard Coat 607?+
No. Diamond Hard Coat 607 is a coating resin only. It is not designed for casting or pouring into moulds.
How much resin do I need?+
As a guide, 1 litre of mixed resin covers approximately 1 m² at 1 mm thick, so the 12L Kit covers about 12 m² at 1 mm. Porous surfaces such as raw timber and canvas absorb more.
How long does it take to cure?+
At 20 °C, a 1–2 mm coat is set in about 1 day and fully cured in about 3 days.
Is Diamond Hard Coat 607 a UV resin?+
No. It is a two-part epoxy that cures when the resin and hardener are mixed. "UV resistant" means it is formulated for enhanced resistance to discolouration from UV light.
How much heat can it handle once cured?+
Once fully cured, it is heat resistant up to 80 °C.
Why is my resin thick or cloudy?+
Resin and hardener can go thick and cloudy in cold weather. Stand the closed bottles in warm water until the liquids are clear and free-flowing, then dry the bottles before you open and mix them.

Safety & storage

Protection
Wear protective gloves and glasses when mixing and using. Always wear a mask when using any solvent cleaner.
Ventilation
Work in a well-ventilated area. Avoid contact with eyes and skin. Over-exposure may cause sensitisation.
Storage
Keep caps on bottles when not in use. Store at room temperature (approx. 18 °C), away from direct sunlight and not on concrete floors.
Clean-up
Clean tools and surfaces with orange citrus solvent, methylated spirits or a resin cleaner. If resin gets on your skin, wipe it off and wash with soap and water. Never use solvents on skin.
Ask a Question
Reviews

Customer Reviews

Based on 5 reviews
100%
(5)
0%
(0)
0%
(0)
0%
(0)
0%
(0)
N
Novianti Lim
Happy

I used a different product before, but decided to try out Solids Solutions Diamond Coat. I am glad i did. Its a better product

J
Joanne Clay

Diamond Hard Coat 607 2:1 | 12L Kit Epoxy Resin

B
Ben Peters
Fantastic stuff

Flows well and happy with the end product

C
Carmen Cummings
Excellent

Love it and will continue to order from you for my business because your products are really good :)

Carmen Cummings review photo Carmen Cummings review photo
S
Steven Coling
Great Service

Perfect resin product and speedy delivery, I buy all my resin from these guys now!